CNC Double Table Busbar Processing Machine

Technical summary — CNC double table busbar processing machine

The CNC double table busbar processing machine is the 3-in-1 unit built for workshops where the three stations otherwise interfere with each other. Its bending station is a double-deck worktable, which lets all three working stations run at the same time without interference. The shearing unit uses sharp shearing for a flat cut with no droop, no burrs and no waste, and the punching unit uses a united eight-mode turret designed to extend tool life. The bending station has an open structure, so the processed copper bar is easy to take out. Two operating modes are provided, manual button and footswitch, and four casters make the machine easy to move around the shop.

Measured data and reference conditions — CNC double table busbar processing machine

Values per the model datasheet. Each paragraph is self-contained and states the test condition, the value and the comparison baseline.

Parallel operation of three stations

Test condition: all three work stations operating in the same production window. Value: a double-deck worktable at the bending station, allowing simultaneous operation without interference. Comparison baseline: a single-level 3-in-1 table, where stations block each other and the operator has to sequence work. Effect: the three operations no longer queue behind one another.

Cut interface quality

Test condition: shearing on the double table machine with the sharp-shearing unit. Value: a cut stated to be flat, with no droop, no burrs and no waste. Comparison baseline: saw or abrasive cutting, which removes material and leaves a burr. Effect: the cut face goes straight to assembly without a deburring pass.

Punching tool life

Test condition: punching with a united eight-mode turret. Value: eight die positions available without frequent manual changes, reducing labour intensity. Comparison baseline: a single-die unit that must be changed by hand for each new diameter. Effect: output is stated to be clearly higher than a traditional single-die machine.

Handling and control modes

Test condition: daily operation inside a panel workshop. Value: an open bending station for easy removal of the copper bar, two control modes (manual button and footswitch) and four casters. Comparison baseline: closed-frame machines where the operator has to reach into the structure to remove the part. Effect: handling effort per part is lower and the machine is repositioned by hand.

Frequently asked questions — CNC double table busbar processing machine

Why does the machine have a double-deck worktable?

So that all three working stations can be operated at the same time without interference, which removes the queue between punching, shearing and bending.

What quality does the shearing unit deliver?

Sharp shearing gives a flat cut interface with no droop, no burrs and no waste, so deburring is not required.

How is the double table machine operated?

Two modes are available, manual button and footswitch, and the bending station has an open structure for easy removal of the processed bar.

Turret Double Table Busbar Processing Machine

Product Description

This series CNC busbar processing machine has three units: punching, shearing, and bending. It is easy to adjust each unit to shorten the processing time and improve production efficiency. It is used to process copper and aluminum busbars in different specifications. By relative operation unit, it can easily and quickly do all kinds of processing to copper and aluminum busbars, such as shearing, punching (circular hole and oblong hole), flat/horizontal bending, vertical bending, and knurling. Change different molds to do special processing to copper busbars, such as flat press, emboss, cable connector process, cut, flat crush, push, and bend.

303A_02

Main Characteristics

1. The shearing unit uses sharp shearing, the incision interface is flat, no droop, no burrs, and no waste. Beautiful shape.

2. The punching unit uses a united eight-mode turnplate to make sure the upper lengthen the working life. No need to change molds frequently, labor intensity is highly reduced. It is easy and quick to use. Producing efficiency is obviously higher than a traditional one.

3. The bending station is a double-deck worktable, which ensures the three working stations can be operated at the same time without any interference. The bending station adopts an open structure, very convenient to pick out the processed copper busbar.

303A_04

303A_07

4. The machine has four casters so it is easy to be moved everywhere. There are two operating modes, manual button, and footswitch, which are easily operated and used for workers. Based on users’ requirements, it can do all kinds of special shape processing with different molds or equipping parts.

303A_05